What are your settings?

Dopey

I-O Full Member

Reputation: 6
Posts: 127

I am teh ninja

What are your settings?

« on: Jul 28, 2009 »

Didnt see this post anywhere. So what are everybodys settings? Post up your dwell/internals/pressures ect. and how well its working as far as accuracy/consistency/speed

Ok so mine are:

-vision board dwell at 5.5-6ms
-lpr according to my gauges number is about 5-10psi Cheesy

(actually about 110psi)
-all evil internals
-main input pressure 195psi


	Logged

+add witty phrase here

Lights Out

I-O Owner
I-O Hero Member

Reputation: 28
Posts: 907

Re: What are your settings?

« Reply #1 on: Jul 28, 2009 »

good topic - i am looking to adjust my WAS board and am curious what other people have for settings.

I will post mine soon as well


	Logged

Lights Out, Camera, Action...

J. Thompson #5150

I-O Full Member

Reputation: 2
Posts: 79

The 280-Pound Gorilla

Re: What are your settings?

« Reply #2 on: Oct 10, 2009 »

I'll go ahead and post my settings. I've done a crap load of tuning on this setup, and have experimented with countless dwell and pressure settings, and even different spring weights for the valve. I think I've got just about as close to perfect as I can get.

NDZ ram housing
NDZ ram
NDZ mid-weight hammer
Evil valve (air passage drilled and polished)
custom ultra light-weight valve spring
Shocktech stubby bolt
NDZ/ANS Jackhammer LPR
Max-Flo vert reg
WAS board (newest flash)

Board: 6ms dwell
LPR: 80psi
HPR: 140psi

Velocity: 290 fps, +/- 5 fps

Efficiency: close to 1000 rounds on a 68/3K


	Logged

Black Impulse Vision: HSW V1 I-Frame, Hybrid grips, WAS board, NDZ eye cover, Max-Flo HPR, Evil LPR, Shocktech bolt, drilled and polished Evil valve, ultralight valve spring, NDZ ram housing, NDZ Slik-Shot ram shaft, NDZ mid-weight hammer, SP Q-Lock lo-rise feedneck, Freak barrel kit, CP on/off

rao

I-O Sr. Member

Reputation: 3
Posts: 157

Re: What are your settings?

« Reply #3 on: Oct 10, 2009 »

how did you drill out that evil valve and do you think it made a difference in air flow? What did you use for a spring? I am running evil internals and LPR, hoping to get pressure down. Was running 7 on dwell, 100 on LPR and 200 on HPR. 285 +/-.


	Logged

Slow_Target

I-O Jr. Member

Reputation: 1
Posts: 39

Re: What are your settings?

« Reply #4 on: Oct 11, 2009 »

Dopey, I hope thats a typo, vision boards start at 4ms. They cannot be set lower then that.
For the record
WAS board
SS Rathole hammer
NDZ valve, slik-shot ram, stubby delrin bolt
Settings
Hpr - 155-160
Lpr - 80
Dwell - 7ms
Debounce - 10 (i think)
BIP - 3


	Logged

Dopey

I-O Full Member

Reputation: 6
Posts: 127

I am teh ninja

Re: What are your settings?

« Reply #5 on: Oct 12, 2009 »

Lol thought they bottomed out at 0. That number did seem incredibly low to me though, original post edited


	Logged

+add witty phrase here

Lights Out

I-O Owner
I-O Hero Member

Reputation: 28
Posts: 907

Re: What are your settings?

« Reply #6 on: Oct 13, 2009 »

W.A.S board
NDZ RIP Valve
NDZ LPR
NDZ HE Assembly w/ Slik Shot Ram & Rat Hole Hammer
NDZ Hammer Cap
NDZ Equalizer Bolt
HSW Delrin Bolt Pin

HPR: 140psi
LPR: 90psi
DWELL: 7ms
DEBOUNCE: 5ms
ROF: 30bps
BIP: 5ms


	Logged

Lights Out, Camera, Action...

J. Thompson #5150

I-O Full Member

Reputation: 2
Posts: 79

The 280-Pound Gorilla

Re: What are your settings?

« Reply #7 on: Oct 20, 2009 »

Quote from: rao on Oct 10, 2009

If by "how" you mean the actual process, I did it on a drill press. The passage is just slightly bigger than the stock valve, which is huge compared to the Evil valve. For a valve spring, well I've had two different setups. With the old Evil LPR I was using a stretched spring from a Spyder valve spring kit. Then after I got the NDZ LPR I actually went to the hardware store. I wanted the lightest spring I could find and ended up with beehive spring. Basically its shape not only fits the cup seal ont he valve, but also seats properly on the volumizer's spring perch. And to add to that, the shape and size allow the spring to operate without binding or the use of a spring guide. Which allows for maximum volume in the dump chamber. As far as the difference it made, well I can only speculate that the added flow made some sort of difference. The day I got the gun, I pulled the valve out, looked at it, and thought no, this small passage just will not do.


	Logged

batfly

I-O Full Member

Reputation: 0
Posts: 53

Re: What are your settings?

« Reply #8 on: Mar 06, 2011 »

Just got back from a field using their chrono. here's a list of what i put into the thing.

NDZ slick shot
NDZ ss mid hammer
NDZ rip valve (thanks Deathss!)
NDZ volumizer with sp lpr
titanium pin
strange bolt
max flow reg
cricket vision

settings:
Hpr 180
Lpr 65
Dwell 7.5
+/- 5 around 290 fps

i went to the field with hpr 160 lpr 60 and dwell at 7 and it was shooting 270 fps +/- 5 . i raised the hpr and it DROPPED to 150-160 fps. so then i raised the lpr and it only went up slightly. so i then upped the dwell 2 beeps to 7.5 ms. and got where i needed to be. i think i went past the pressure bell curve and have too much hpr to the rip valve (too much pressure on the valve's cup seal causing me to counter with more dwell or lpr pressure wasting gas). i've heard of this happening with rip valve above 160-165 psi. i should have backed off the hpr till there was no more gain. then increased lpr leaving the dwell at 7. crazy how much more flow goes through the rip valve. rather impressive!

i realized what more needed to be experimented with, but by this time the field started getting tons of people so i couldn't tweak any further. did let the ref (about 19 years old) shoot my imp though, he thought it was sweet! he was impressed at my rear port tester gauge hack job. lol

think i'm going to buy a chono next paycheck


	Logged

Impulse-Owners


	Logged

Pages: [1]

« previous next »